Jump to content


Photo
- - - - -

Painting Inlet / Exhaust Manifolds


  • Please log in to reply
10 replies to this topic

#1 cooperd70

cooperd70

    Super Mini Mad

  • TMF+ Member
  • PipPipPipPipPipPip
  • 653 posts
  • Location: London

Posted 17 January 2019 - 05:56 PM

If using high temp paint is it worth it to try and keep the temp contained within the exhaust manifold/shstem without having to use a wrap, which I'm lead to believe can bring on premature cracking around welds.

If paint is the way to go and the manifold is not brand new, should it be treated to one of the many rust inhibitor gels on the market after cleaning, but before high temp paint is applied?

#2 nicklouse

nicklouse

    Moved Into The Garage

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPipPipPip
  • 17,900 posts
  • Location: Not Yorkshire
  • Local Club: Anonyme Miniholiker

Posted 17 January 2019 - 06:17 PM

not worth it not found one that does not burn off. and the paint does not contain the heat. wrapping just shifts the heat under the car which can result in burn paint in the tunnel.



#3 hhhh

hhhh

    Speeding Along Now

  • Members
  • PipPipPipPipPip
  • 422 posts

Posted 17 January 2019 - 06:24 PM

How about ceramic coating, lasts better than paint and keeps the heat in.



#4 nicklouse

nicklouse

    Moved Into The Garage

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPipPipPip
  • 17,900 posts
  • Location: Not Yorkshire
  • Local Club: Anonyme Miniholiker

Posted 17 January 2019 - 06:32 PM

How about ceramic coating, lasts better than paint and keeps the heat in.

only give about a 30% reduction and you burn paint off further down the car.



#5 hhhh

hhhh

    Speeding Along Now

  • Members
  • PipPipPipPipPip
  • 422 posts

Posted 17 January 2019 - 06:45 PM

Probably keeps the intake charge cooler though. I'll suffer a little burnt paint in the tunnel for a couple of HP.



#6 Icey

Icey

    One Carb Or Two?

  • Traders
  • PipPipPipPipPipPipPip
  • 1,490 posts
  • Location: Wiltshire

Posted 17 January 2019 - 11:36 PM

You’re not likely to see any power increase that isn’t a rounding error. The only reason to pursue it is if you’re struggling with under bonnet temperatures.

If you haven’t already, you’re better spending your money on an improved cylinder head, cam and a RR session.

#7 nicklouse

nicklouse

    Moved Into The Garage

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPipPipPip
  • 17,900 posts
  • Location: Not Yorkshire
  • Local Club: Anonyme Miniholiker

Posted 17 January 2019 - 11:47 PM

Probably keeps the intake charge cooler though. I'll suffer a little burnt paint in the tunnel for a couple of HP.

a couple of BHP. no way. a fraction may be. but like i have said yet to find one that lasts any length of time.



#8 hhhh

hhhh

    Speeding Along Now

  • Members
  • PipPipPipPipPip
  • 422 posts

Posted 18 January 2019 - 04:14 AM

I think the combination of lower intake temperature and higher speed exhaust could feasibly give a 2% increase in HP.



#9 luismx123

luismx123

    Super Mini Mad

  • Members
  • PipPipPipPipPipPip
  • 525 posts
  • Location: Graz

Posted 18 January 2019 - 07:32 AM

I think the combination of lower intake temperature and higher speed exhaust could feasibly give a 2% increase in HP.

not an expert, but I think if it would do that then everyone would know about it by now. There must be quite a few people that have tried it before



#10 Steve220

Steve220

    Up Into Fourth

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPip
  • 4,877 posts
  • Location: Shropshire
  • Local Club: RAF Mini Club

Posted 18 January 2019 - 09:30 AM

The boys on the evo forum did back to back results, will see if I can dig out the link.

Ceramic coating is worth it mainly for engine bay temps and turbo applications in my opinion. The key to its application is in the prep work by the company applying it. I had a turbo manifold done on my old evo 9 and it was rock solid for the 2 years of hell I put it through.

#11 cooperd70

cooperd70

    Super Mini Mad

  • TMF+ Member
  • PipPipPipPipPipPip
  • 653 posts
  • Location: London

Posted 18 January 2019 - 02:57 PM

The boys on the evo forum did back to back results, will see if I can dig out the link.

Ceramic coating is worth it mainly for engine bay temps and turbo applications in my opinion. The key to its application is in the prep work by the company applying it. I had a turbo manifold done on my old evo 9 and it was rock solid for the 2 years of hell I put it through.


Cheers Steve ?




1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users