Jump to content


Photo
- - - - -

Nut & Bolt Rebuild With Added Type-R


  • Please log in to reply
61 replies to this topic

#1 Harry L

Harry L

    Stage One Kit Fitted

  • Noobies
  • PipPipPip
  • 63 posts
  • Location: United Kingdom

Posted 29 May 2020 - 02:50 AM

This is my build of a Mini City with a Honda B16B engine swap, the aim of the build is purely to be a fast street car to take on roadtrips and sunny day drives. It will be kept as 'Mini' as possible and I'm aiming to complete the engine conversion with minimal body modifications, it will be a fully bolt in conversion and completely reversible in the future if desired!

 

 

First step as with most Minis was the bodywork. This was the state of the car once the bodyshop had blasted the shell down to bare metal to ascertain the full extent of the rust.
 

49735475881_26bb9dfa13_b.jpg

49735804142_12ed798893_b.jpg

49735476031_c00271952d_b.jpg

49734933058_72501d01cf_b.jpg

 

 

In the end, the following panels were replaced:
  • Front floor
  • Rear quarters
  • Door skins
  • Inner and outer sills
  • Scuttle panel
  • Full front end
  • Boot floor
  • Rear arches
  • Heel board
 
Here are some photos of the repaired shell in primer
 

49735475916_ff8d1f784e_b.jpg

49735804122_7c332c60ca_b.jpg

49734933068_6b2e0df823_b.jpg

 

 

And then it was time for some paint!
 

49734932888_2db3cd04fc_b.jpg

49735474941_9443207ea8_b.jpg

49734932053_9bc182caac_b.jpg

49735475091_5e940ac7f1_b.jpg

49735804207_372a87439a_b.jpg

49734932398_fd0e54df70_b.jpg

49734932778_2c07e21d91_b.jpg

 

 
And this is the shell after the final flatting back and compounding, really happy with the colour, it's absolutely gorgeous in the sun  :D
 
49734931713_6305ef3d56_b.jpg

49735803247_9a9b10ec17_b.jpg

49735803337_70280ef7a8_b.jpg

49735475126_b365e26a17_b.jpg

 

The work was done by Fusion Bodywork in Northampton and I'm not massively impressed with the standard of the job at all but it was extremely cheap at £2000 and it is at least now solid and one colour!
 
 
Stay tuned on this one, lots more to come, I'm getting through it over the next few nightshifts!

Edited by Harry L, 10 January 2023 - 04:26 AM.


#2 Harry L

Harry L

    Stage One Kit Fitted

  • Noobies
  • PipPipPip
  • 63 posts
  • Location: United Kingdom

Posted 29 May 2020 - 03:22 AM

Now these next photos might seem all over the place as they were taken over a number of years, the project had been put on hold at various stages and lots of things happened in different orders.
 
 
I started with the rust proofing, Dynax S50 in the cavities and Dynax UC on the underside and arches.
 
49735475716_a5f72aa1f7_b.jpg

49735803877_1d7b679da5_b.jpg

 
Mk1 glass indicators fitted
 
49735475761_75ccf5acdc_b.jpg

 

 
Mk2 rear lights fitted, with LED bulbs - this is a 21st century Mini  :D
 
49757493041_f56d315f3b_b.jpg
49735475636_85a6f1fe3a_b.jpg

 

 
Black suede headlining fitted
 
49947550477_37f73a6659_b.jpg

49946761798_68a4e94f10_b.jpg

 

 
Doors built up, and all glass, mirrors etc. fitted
 
49947265076_d54ddc05a2_b.jpg

49947263931_5ee85951c2_b.jpg

49747440367_338d3a7138_b.jpg

49747440492_86f3ac4b46_b.jpg

49735893717_99f145cd80_b.jpg

49738773577_b66f27b3db_b.jpg

49735023883_f51c6fecb8_b.jpg

 

 
Next up was running the Kunifer brake and fuel lines, fixed with stainless p-clips and rivnuts
 

49747440462_4ee2119ec7_b.jpg

49747440292_814099bb71_b.jpg

49757491796_66cc25bcd3_b.jpg

 

 
Also ran the battery cable through the car
 
49757827777_251a2c1311_b.jpg

49794262857_6e753674fc_b.jpg



#3 I hate Brian

I hate Brian

    One Carb Or Two?

  • Members
  • PipPipPipPipPipPipPip
  • 770 posts
  • Location: nottingham

Posted 29 May 2020 - 04:10 PM

Hi are you keeping the car running as an SPI ?



#4 Harry L

Harry L

    Stage One Kit Fitted

  • Noobies
  • PipPipPip
  • 63 posts
  • Location: United Kingdom

Posted 29 May 2020 - 04:51 PM

Hi are you keeping the car running as an SPI ?

Nope, I have a B16B to go in it  ;-)



#5 Harry L

Harry L

    Stage One Kit Fitted

  • Noobies
  • PipPipPip
  • 63 posts
  • Location: United Kingdom

Posted 29 May 2020 - 04:59 PM

With the shell pretty much all built up and watertight, I started work on the subframes, ready to get the car rolling.
 
I bought a second hand rear subframe that had been gusseted and seam welded for strength and also galvanised. First step was to strip off the old paint and then I coated it in stonechip and truck bed liner.
 

49735023828_801661c957_b.jpg

49735023848_9d4bd9af43_b.jpg

49735023903_dca61d9f19_b.jpg

 
 
And fitted to the car, the brand new rubber bushes lasted literally a week of not being driven before they split, Minispares quality for you  =]
 
49747111801_bd455a8ae5_b.jpg
49747112021_c6c18b9ca2_b.jpg

 

 
Some parts being refurbed with truck bed liner, I love the really hard wearing textured finish this gives. 
 
49757827792_8ed88eb22c_b.jpg

49756967423_8dbfc2fc09_b.jpg

 

 
Time to get started on building the subframe up, new genuine cones, radius arms, HiLos and AGX dampers fitted
 

49757492076_75eab885bb_b.jpg

49757493011_13be1eb178_b.jpg

 

 

Rear brakes and hubs built up with genuine Timken bearings, new back plates, Mintex shoes and finned alloy drums - these are so light!
 
49757493036_3df2f397fc_b.jpg

49793956341_dfaf71e148_b.jpg

 



#6 Harry L

Harry L

    Stage One Kit Fitted

  • Noobies
  • PipPipPip
  • 63 posts
  • Location: United Kingdom

Posted 29 May 2020 - 05:09 PM

Took a break from suspension and subframes and got a few interior bits done, heater unit stripped and rebuilt with new foam
 
49794262822_bbf343fa15_b.jpg
 
 
Got the heater fitted alongside an MPI steering column and stalks, makes the car feel a lot newer and higher quality!
 

49794262732_8702fae287_b.jpg

 

 

Ordered a bulk pack of Silent Coat and got that fitted in the key areas, and no, 100% coverage is not needed!

 

49948557693_a9754c72e2_b.jpg

 

 

Personal steering wheel fitted, absolutely love this thing

 

49949315052_53a198ddc5_b.jpg

 

 

I also started work on the engine bay, I cut out the inner arches completely to give me good clearance for the engine, all painted up and you wouldn’t even know it’s not factory :D Not planning on doing any bulkhead mods, going to have the inlet manifold modified instead.
 
49875267651_88a2c458dd_b.jpg
49875266701_c136fba777_b.jpg

49875270236_31e5523451_b.jpg

 

 

Clutch master cylinder fitted, this has been modified to work with the Mini's pedal so should have perfect travel.

 

49874735558_7136980efd_b.jpg

 



#7 Harry L

Harry L

    Stage One Kit Fitted

  • Noobies
  • PipPipPip
  • 63 posts
  • Location: United Kingdom

Posted 29 May 2020 - 05:39 PM

Very exciting day :D  The Allspeed Engineering front subframe has arrived and it’s a very nice piece of kit, you can tell actual engineering has gone into this and it hasn’t just been thrown together using an old Mini subframe.
 
49875266496_0de9d0c70d_b.jpg
49874735513_96dae5d897_b.jpg

 

 
Got straight to painting it, chosen coating this time was Frost Ultimate Chassis Black, really happy with this stuff, it’s so tough and should be a lot more durable than powdercoat.
 

49874736783_f2e1cfdbed_b.jpg

49875269966_03d8e791c9_b.jpg

49875579142_e4d6558464_b.jpg



#8 Harry L

Harry L

    Stage One Kit Fitted

  • Noobies
  • PipPipPip
  • 63 posts
  • Location: United Kingdom

Posted 29 May 2020 - 05:45 PM

Subframe fitting time! Went on okay, had to trim a few areas for more clearance but I'm really happy with the fitment.
 
New cones and top arms fitted, you have to use two of the thick thrust washers on these subframes, all goes together really well - very impressed!
 

49875578747_b35d73a6f9_b.jpg

 

 

Lined up, ready to fit

 

49875579442_f1f8fa3a37_b.jpg

 

 

In place and bolted tight

 

49874735533_a83320fc4c_b.jpg

 

 

This meant I could now fit the rose jointed lower arms and get it ready to build up the suspension!

 

49875578457_be45b29c42_b.jpg

 

 

Few bits fitted in the engine bay such as the wiper motor and brake servo, fitted the front dampers and this is how it was left for the day

 

49874734773_f8406b55af_b.jpg

 

 

The subframe will have to come out again to fit the engine as it doesn’t fit from above but I wanted to make sure it all fitted okay before I got too committed!


#9 Steve220

Steve220

    Up Into Fourth

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPip
  • 4,877 posts
  • Location: Shropshire
  • Local Club: RAF Mini Club

Posted 29 May 2020 - 06:12 PM

Out of curiosity, what did you have to trim to give the subframe more clearance?

Edited by Steve220, 29 May 2020 - 06:13 PM.


#10 Harry L

Harry L

    Stage One Kit Fitted

  • Noobies
  • PipPipPip
  • 63 posts
  • Location: United Kingdom

Posted 29 May 2020 - 06:18 PM

Out of curiosity, what did you have to trim to give the subframe more clearance?

Couple of bits on the front panel and the part where the suspension towers are, as expected really. I think most people take the front end off and fit a fibreglass flip-front but I wanted to keep the shell as original as possible.



#11 Steve220

Steve220

    Up Into Fourth

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPip
  • 4,877 posts
  • Location: Shropshire
  • Local Club: RAF Mini Club

Posted 29 May 2020 - 07:06 PM

 

Out of curiosity, what did you have to trim to give the subframe more clearance?

Couple of bits on the front panel and the part where the suspension towers are, as expected really. I think most people take the front end off and fit a fibreglass flip-front but I wanted to keep the shell as original as possible.

 

Thanks chap. I'd heard similar about the allspeed subframes, but wanted to get the info direct from someone who's doing a resto :)



#12 Harry L

Harry L

    Stage One Kit Fitted

  • Noobies
  • PipPipPip
  • 63 posts
  • Location: United Kingdom

Posted 29 May 2020 - 07:29 PM

Right so about this engine!
 
It’s a JDM Honda B16B, this engine is particularly special as it only came in one car, the EK9 Civic Type-R, which was only ever sold in Japan. It also has the LSD S4C gearbox. Mileage was unknown but an inspection of the bores still shows the honing marks, the car also drove okay, made no smoke and sounded good, so I’m happy! 
 
I also have a Spoon ECU for the engine, this essentially adds about 15hp, increasing the rev limit to 9k RPM(!) and lowers the VTEC engagement point for better drivability, should be seeing close to 200hp with this, amazing for an NA 1.6 from the 90s.
 
Here it is in the donor and on the day it was removed
 
49793416088_a60bded2f5_b.jpg

49793416048_d12bd4e50f_b.jpg

49875576897_8537cb620f_b.jpg

49949820142_0c12592a68_b.jpg

 

 
Had to get the engine shipped to me as we were still in #coronalockdown and I didn’t fancy getting pulled over with an engine in the boot :lol: Turns out for the sake of £50 it was worth it to save the hassle anyway! Here it is waiting to be stripped.
 
49949029393_95f46a362c_b.jpg

 



#13 Harry L

Harry L

    Stage One Kit Fitted

  • Noobies
  • PipPipPip
  • 63 posts
  • Location: United Kingdom

Posted 29 May 2020 - 07:32 PM

Been stockpiling some parts for the engine refresh, only genuine Honda parts will do here. In this box we have a full gasket set, clutch kit, cambelt kit, and a longer 5th gear set, to bring the revs down at crusing speed!
 
49949450321_1f640cc74e_b.jpg

 

 
And an MFactory 4.0 final drive to make this slightly more drivable on the Mini’s smaller wheels. Lots of people fit a 3.4 FDR but I wanted to keep the revvy characteristics of the engine, should be similar to a stock Civic now
 

49946661793_1a07aaafa0_b.jpg

 

 

Really excited to get stuck in with engine work!

 



#14 Harry L

Harry L

    Stage One Kit Fitted

  • Noobies
  • PipPipPip
  • 63 posts
  • Location: United Kingdom

Posted 29 May 2020 - 07:39 PM

Engine strip down begins, my plan is to do a fairly basic overhaul and light refresh, it’s a solid unit so pointless going too far with it, I just want to get it in and drive it.
 
49875270216_c6ffd052b8_b.jpg
49949530411_9c20491d0f_b.jpg
 
 
Engine on the stand and having a deep clean ready for a coat of paint.
 
49875576002_73e74d7cc5_b.jpg

49875269891_52aa50323b_b.jpg

49947465172_f9866867bd_b.jpg

 



#15 Harry L

Harry L

    Stage One Kit Fitted

  • Noobies
  • PipPipPip
  • 63 posts
  • Location: United Kingdom

Posted 29 May 2020 - 09:56 PM

Time to get this thing ready to get on its wheels!
 
First up was to get the hubs built up, only genuine Timken bearings on this build, mated to the Allspeed uprated CV joints, the known weak point of a Mini’s drivetrain
 
49874736113_2bcc2f1d58_b.jpg

 

 
New balljoints fitted and these were mounted to the car, along with the steering arms and new track rod ends
 
49875578132_137138412e_b.jpg

 

 
Time for brakes :D Minisport 7.9” 4 pots, they look excellent and feel really good quality, easily on par with the £1.2k Brembos on my daily 
 
49875578392_5193bfc431_b.jpg
 
 
These were fitted up along with Minisport's EN24 hardened drive flanges and Goodridge braided lines
 

49875578862_ae8ec57cd5_b.jpg

49875578902_8e2b9f4dca_b.jpg

49874735373_a07df68a40_b.jpg

 

 
Fitted the Wilwood brake proportioning valve and ran the Kunifer hard lines to the front brakes. 
 
49947457097_620a17645c_b.jpg
 
Really pleased with how it's coming together so far!





1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users