Jump to content


Photo

Headlining Fitting Instructions


  • Please log in to reply
36 replies to this topic

#16 stickycreambun

stickycreambun

    Camshaft & Stage Two Head

  • TMF+ Member
  • PipPipPipPipPipPipPipPip
  • 1,865 posts
  • Location: Bath, Somerset

Posted 02 March 2008 - 03:01 PM

what was the leccy tape for...?

:dontgetit:

#17 panelbeaterpeter

panelbeaterpeter

    Crazy About Mini's

  • Members
  • PipPipPipPipPipPipPipPipPipPip
  • 5,606 posts
  • Location: Scotland
  • Local Club: n/a

Posted 02 March 2008 - 03:08 PM

Well spotted! I put it over the lip that the window rubber sits on before applying the rubbers, makes for a better seal and stops any moisture creeeping in the join between panels.

#18 stickycreambun

stickycreambun

    Camshaft & Stage Two Head

  • TMF+ Member
  • PipPipPipPipPipPipPipPip
  • 1,865 posts
  • Location: Bath, Somerset

Posted 02 March 2008 - 03:15 PM

oh right is that so? have to remember that, all my seals and headlining are getting replaced in the near future...

*wonders if Chris is reading...*

#19 bert998

bert998

    Up Into Fourth

  • Members
  • PipPipPipPipPipPipPipPipPip
  • 2,558 posts

Posted 02 March 2008 - 11:24 PM

oh right is that so? have to remember that, all my seals and headlining are getting replaced in the near future...

*wonders if Chris is reading...*



oh dear, here we go again :)


:D

#20 M1N1C00P3R1275

M1N1C00P3R1275

    Mini Mad

  • Members
  • PipPipPipPip
  • 258 posts
  • Local Club: Minifinity

Posted 06 March 2008 - 09:36 PM

this guide is great my headliners goin in soon

#21 sherly

sherly

    One Carb Or Two?

  • Members
  • PipPipPipPipPipPipPip
  • 704 posts
  • Location: Saaaa'fend

Posted 27 March 2008 - 12:32 PM

Anyone fitted a headlining on a car with a webasto roof? I've got to do mine next week and I'm a little unsure on how to tackle fixing the headlining when there's a damn great hole in the roof......?

Initial thoughts were to fit the headlining with all the bars in place as normal and once dry/taught cut the bars/headlining which cover the webasto hole and glue the headlining around the webasto hole using the same method as used for the windscreen/rear quarters etc.

Can anyone elaborate?

#22 Southy

Southy

    Camshaft & Stage Two Head

  • Members
  • PipPipPipPipPipPipPipPip
  • 1,579 posts
  • Local Club: Oldham and Distrcit Mini Club

Posted 28 March 2008 - 05:24 PM

Anyone fitted a headlining on a car with a webasto roof? I've got to do mine next week and I'm a little unsure on how to tackle fixing the headlining when there's a damn great hole in the roof......?

Initial thoughts were to fit the headlining with all the bars in place as normal and once dry/taught cut the bars/headlining which cover the webasto hole and glue the headlining around the webasto hole using the same method as used for the windscreen/rear quarters etc.

Can anyone elaborate?

My clubby has a webatso roof fitted and for this for starters you will need to visit your local sunroof specialist and get the rubber trim which will fit on the inside of the roof opening (unless you already have it)

If you look at the inside of the car of the frame for the webatso roof you will see a slight recess just below the roof.What i did i lined my bars up across the roof and just marked about 1/2cm in from the outter edge of where the recess starts and then using a pair of tin spins cut these ends of the bars off and then use a pair of pliers to flatten the ends out so they will fit inside the gap.

Place these ends of the bars into the lining as you would do normally and feel in the sleeves where the bar finishes and slice open the sleeve about 1 cm before the end. Fit the headlining into the car as stated in the guide above and then slide the flat end of the bar into the recess.

Fit the rest of the headlining as normal (make sure your roof is open/removed) and then with a helper, make a X in the headling in the roof opening about 2 inch in from each of the corners and then apply glue onto the lip.Then get your helper to pull the lining up and out of the roof and pull back against itself nice and tight, then with yourself inside the car, knock on the rubber trim and then cut the excess material off afterwards

#23 sherly

sherly

    One Carb Or Two?

  • Members
  • PipPipPipPipPipPipPip
  • 704 posts
  • Location: Saaaa'fend

Posted 07 April 2008 - 11:38 AM

Cheers Southy - that all seems to make sense! The job still scares me but I'm sure it'll be OK.... :thumbsup:

Oh - I think my roof is a Britax rather than a webasto but I'm sure the same applies. I don't remember removing a rubber seal when I took the roof off, it was masticed on the outside. This is probably down to it being bodged when fitted in the first place tho'.

Edited by sherly, 07 April 2008 - 11:41 AM.


#24 Southy

Southy

    Camshaft & Stage Two Head

  • Members
  • PipPipPipPipPipPipPipPip
  • 1,579 posts
  • Local Club: Oldham and Distrcit Mini Club

Posted 10 April 2008 - 06:32 AM

No problem at all sherly be sure to post some finished pictures up so we can see the results. >_<

#25 lilmatti69

lilmatti69

    Learner Driver

  • Noobies
  • PipPip
  • 20 posts

Posted 19 April 2008 - 05:15 AM

hey mate nice how-to, i justs have one question my bars arnt the same colours as yours, mine are:
not in correct order
Yellow
yellow
orange
brown
red
Nothing.

do you know wa=hat order they go in?

thanks

#26 Southy

Southy

    Camshaft & Stage Two Head

  • Members
  • PipPipPipPipPipPipPipPip
  • 1,579 posts
  • Local Club: Oldham and Distrcit Mini Club

Posted 19 April 2008 - 09:56 PM

Hmmm i cant say i do, do you know who produced the kit and did it come with any instructions at all?If you have an old one lay about with the correct bars then could check them agsint that to see which are the same shape.

The 2 yellow bars will be the white ones in my how-to and if its correct the red bar will be the first bar at the front, as for the rest i cant really say, might be best speaking to whoever you bought the kit off and see what they say regarding the correct order.

#27 Southy

Southy

    Camshaft & Stage Two Head

  • Members
  • PipPipPipPipPipPipPipPip
  • 1,579 posts
  • Local Club: Oldham and Distrcit Mini Club

Posted 12 May 2008 - 10:08 PM

Just bought my newton commercial headliner last week, not even ready for it yet for my car but after the waiting time it took when i last ordered one i placed the order in sooner, only to have it arrive the next day ;D

So may well end up updating this thread later on this year with pictures for more ease of reading and to let you all see how its done

#28 marco.h

marco.h

    Mini Mad

  • Noobies
  • PipPipPipPip
  • 116 posts
  • Local Club: Not got joined yet....

Posted 22 August 2008 - 09:29 PM

Fitted mine yesterday, forgot the instructions on here, so made it up as I went along! I used "timebond" evo stick glue stuff, worked great, put it on either side and leave for 5 mins, then attach. Even when pulled tight it didn't come undone, I had a load of bulldog clips, but they weren't really needed.

Posted Image


Peter, where did you get your headlining from as it looks to be perforated...

is it the newton commercial one for an innocenti mini?
would that be ok to use in my 92 Cooper?

cheers

#29 panelbeaterpeter

panelbeaterpeter

    Crazy About Mini's

  • Members
  • PipPipPipPipPipPipPipPipPipPip
  • 5,606 posts
  • Location: Scotland
  • Local Club: n/a

Posted 22 August 2008 - 11:54 PM

Got mine from Retro Retrims, or Bert 998 off here. Very nice it was too, and easy to fit.

#30 minidan

minidan

    Up Into Fourth

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPip
  • 2,354 posts
  • Local Club: LSMOC

Posted 26 August 2008 - 02:42 PM

just finished putting in my headlining . i tried to follow the guide but ended up doing some of it my own way. still a very helpful guide.
also i did the whole thing on my own and i think a 2nd person would have been very helpful! anyway heres some pics.

Posted Image
Posted Image




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users