What Spec Is Your Engine?
Started by
Bluemini
, May 22 2005 08:21 PM
197 replies to this topic
#46
Posted 19 July 2005 - 07:49 PM
Here's the NEW spec on my 1330..
- 1300GT solid wall A series block bored to +.060
- 21253 HC cooper pistons rising just proud of block deck (11-12:1 CR unverified)
- 1300GT 11 stud head, 1.4" inlet 1.1" exhaust bronze guides std rockers, cleaned up ports and combustion chamber ( probaby equiv to stage 2 )
- Tuftrided crank
- Ultralight billet steel flywheel & Back plate
- Early Kent 290 cam timed @ 105 degrees, fully adjustable vernier silent chain timing gear.
- A series helical drops.
- A series Close Ratio GT gearbox with 3.44 CWP on a X pin Diff.
- HIF44 with modified BBC needle 8 oz spring and K&N
- Phase 2 Maniflow LCB hooked to 1.3/4" single box RC40
ooh.. forgot about ignition..
- lucas sports coil
- BP7ES plugs
- Modified Aldon 100AY dizzy, using sliding points and vacuum advance.
30 miles old, and doing the 1/4 in 16.45 on std 145/70x12's
Needs a tune and probably capable of going sub 16 for the 1/4.
- 1300GT solid wall A series block bored to +.060
- 21253 HC cooper pistons rising just proud of block deck (11-12:1 CR unverified)
- 1300GT 11 stud head, 1.4" inlet 1.1" exhaust bronze guides std rockers, cleaned up ports and combustion chamber ( probaby equiv to stage 2 )
- Tuftrided crank
- Ultralight billet steel flywheel & Back plate
- Early Kent 290 cam timed @ 105 degrees, fully adjustable vernier silent chain timing gear.
- A series helical drops.
- A series Close Ratio GT gearbox with 3.44 CWP on a X pin Diff.
- HIF44 with modified BBC needle 8 oz spring and K&N
- Phase 2 Maniflow LCB hooked to 1.3/4" single box RC40
ooh.. forgot about ignition..
- lucas sports coil
- BP7ES plugs
- Modified Aldon 100AY dizzy, using sliding points and vacuum advance.
30 miles old, and doing the 1/4 in 16.45 on std 145/70x12's
Needs a tune and probably capable of going sub 16 for the 1/4.
#47
Posted 26 July 2005 - 08:29 PM
1275cc standard cooper S
+ K&N air filter, dunno whether it worth it buying an rc 40 2.25"
+ K&N air filter, dunno whether it worth it buying an rc 40 2.25"
#48
Posted 26 July 2005 - 08:45 PM
1275 SPi - stage one I guess
LCB, K&N cone, cat removal, single box rc40
LCB, K&N cone, cat removal, single box rc40
#49
Posted 26 July 2005 - 09:35 PM
1275 with k&n and straight through exhaust and twin dtm exhaust.
#50
Posted 26 July 2005 - 10:14 PM
mine is a 1liter
#51
Posted 12 August 2005 - 02:52 PM
998 with a stage one
#52
Posted 14 August 2005 - 11:09 AM
Just recently bought a 1.4 16v k series mini With is currently being tranfered into my hornet. I've aslo just bought a 1.8 elise bottom end which will be getting sent away for a lighten and balance. And also in the process of buying some twin 45 webers :grin:
#53
Posted 24 August 2005 - 03:31 PM
I have a 1275 MG Metro lump. RC40 Exaust system, miniflow manifold, new carb needle, K&N cone filter on a HIF44 1.75" CARB, minisport water heated inlet manifold, Duplex timing gear, Kent fast road cam,double valve springs,sports clutch and a lightned flywheel. Standard metro gearbox with quickshift. Fully stripped and rebuilt. (still running it in :sad: )
#54
Posted 24 August 2005 - 05:35 PM
1275A+
Stage 1
Single box rc40
Additional fan on switch.
Stage 1
Single box rc40
Additional fan on switch.
#55
Posted 24 August 2005 - 06:39 PM
i have a 998 with a stage one in the van, and a 998 with a rc40 on the othere (i think still have to pick the car up yet) but thats getting replaced with a 1275 soon
#56
Posted 26 August 2005 - 07:25 AM
Mines a 1275 RSP block and box with an unleaded head, electronic Ignition, mild cam, three branch and RC-40 (stage 1) with oil cooler for good measure!!
Thats about it
Thats about it
#57
Posted 06 September 2005 - 07:34 AM
Our mini is just a 998, with no modifications. We really want to keep it as original as possible too - so no mods planned just yet.
#58
Posted 06 September 2005 - 08:52 AM
Right now I have the 1275CC SPI engine. No mods done to it yet.
#59
Posted 06 September 2005 - 09:29 AM
Soon I'll be getting myself a 1293 stage 3 minisport engine
It'll have about 80-100 BHP come on you chav boyracers....
It'll have about 80-100 BHP come on you chav boyracers....
#60
Posted 13 September 2005 - 11:33 AM
1293 Spamspeed Special in the clubbie till I get the pickup finished
1275 Block bored 20 thou
Reground and tuftrided crank
Cooper S conrods
AE Hepolite Pistons
Turbo Oil Pump
Spam 28 Camshaft
Stage 4 Head (Big Valves )
1.5 Roller Tip Rockers
Central oil pickup
3.7 Diff
Maniflow Big Bore Manifold
RC40 Single Box
HIF44 Carb
Should put out about 85+BHP Hopefully
1275 Block bored 20 thou
Reground and tuftrided crank
Cooper S conrods
AE Hepolite Pistons
Turbo Oil Pump
Spam 28 Camshaft
Stage 4 Head (Big Valves )
1.5 Roller Tip Rockers
Central oil pickup
3.7 Diff
Maniflow Big Bore Manifold
RC40 Single Box
HIF44 Carb
Should put out about 85+BHP Hopefully
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users