Jump to content


Photo

Steering Rack Swap


  • Please log in to reply
23 replies to this topic

#16 icklemini

icklemini

    Up Into Fourth

  • Traders
  • PipPipPipPipPipPipPipPipPip
  • 2,982 posts
  • Location: Northampton

Posted 04 December 2008 - 09:48 PM

undo and removethe pinch bolt at the bottom of the column.

using a suitable lever - separate the clamp slightly.. column should then break its grip on the splines.

#17 eden7842

eden7842

    One Carb Or Two?

  • Members
  • PipPipPipPipPipPipPip
  • 907 posts

Posted 07 December 2008 - 05:18 PM

do i take my column from the rack or the rack from the column? its a tad rusty therefore seized on

#18 icklemini

icklemini

    Up Into Fourth

  • Traders
  • PipPipPipPipPipPipPipPipPip
  • 2,982 posts
  • Location: Northampton

Posted 07 December 2008 - 06:10 PM

column from the rack - am sure its in the haynes if you need a reference..

#19 eden7842

eden7842

    One Carb Or Two?

  • Members
  • PipPipPipPipPipPipPip
  • 907 posts

Posted 13 December 2008 - 03:58 PM

does the bolt in the clamp at the base of the column tighten to the clamp or is it just the nut on the end

mine seems to be very seized

#20 icklemini

icklemini

    Up Into Fourth

  • Traders
  • PipPipPipPipPipPipPipPipPip
  • 2,982 posts
  • Location: Northampton

Posted 13 December 2008 - 06:30 PM

Tightens to the nut on the end - though it is a snug fit in the groove in the spline that comes out of the rack...

#21 bloomers

bloomers

    One Carb Or Two?

  • Members
  • PipPipPipPipPipPipPip
  • 815 posts

Posted 21 December 2008 - 07:52 PM

Hello, Good thread to start. Im going to be doing this shortly, Why do the ball joints have to split? Can you not take the rack off without doing this?

Cheers
Ian

#22 icklemini

icklemini

    Up Into Fourth

  • Traders
  • PipPipPipPipPipPipPipPipPip
  • 2,982 posts
  • Location: Northampton

Posted 25 December 2008 - 09:43 PM

they dont need to be split... though you need to split the trackrod ends from the steering arms....

#23 mozzo1

mozzo1

    Mini Mad

  • Members
  • PipPipPipPip
  • 287 posts
  • Local Club: none

Posted 02 January 2009 - 12:00 PM

dors any one know if i can just support the front of the sub frame and lower the back as iv only got one bottle jack that i can get my hands on, but at the same time i dont want to break anything else as the bill is just getting silly amounts at the mo
. thanks to minidave for them wicked easy readable directions its done now and had to borrow two jack as after looking at job i think this is the only posible way to do it

Edited by mozzo1, 02 January 2009 - 05:11 PM.


#24 Wombat

Wombat

    Learner Driver

  • Noobies
  • PipPip
  • 13 posts

Posted 27 January 2009 - 02:33 AM

When installing do the U bolts up loose initially (so rack can still move) Then install the column making sure the splins are right down and home - do up the pinch bolt tight THEN tighten the U bolts - that way you will have the splines in line and won't strip if the rack is not square to the column.

Edited by Wombat, 27 January 2009 - 02:36 AM.





0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users