Hi
They fit perfectly in the aperture if you opt for bond/rivet ones so that won't be a problem. And yes either shouldn't be a problem, if you would like to give my Dad Tony a call on 07977 231876 he'll be happy to assist with the vents or hole locations. We can fit them or cut holes no problem for you.
Cheers
Dan
Acw Motorsport Plastics - 10% Off Polycarbonate Window Kits
Started by
mini-man-dan
, Dec 03 2010 04:31 PM
48 replies to this topic
#16
mini-man-dan
-
- Traders
-
- 2,684 posts
Up Into Fourth
- Location: Bristol
- Local Club: J19 Mini Owners Club
Posted 11 June 2011 - 09:59 PM
#17
mini-man-dan
-
- Traders
-
- 2,684 posts
Up Into Fourth
- Location: Bristol
- Local Club: J19 Mini Owners Club
Posted 20 September 2011 - 05:39 PM
We will be at Castle Combe's Mini World Action Day this weekend so be sure to come over and have a look. If all goes to plan we will be bringing up 5 full Mk3+ kits to sell on the day, so take advantage of no P&P cost! It will be a first come first serve basis though, so get there early as we don't expect they will hang around very long as we will be offering 10% off to everyone on the day.
Cheers
Dan
Cheers
Dan
#18
TopCatCustom
-
- Members
-
- 1,134 posts
Previously known as C4NN0N.
Posted 27 October 2011 - 04:34 PM
Is the rear window pre-stressed/curved or just supplied flat? If not is there any way of bending it perhaps over a glass screen with a heat gun or not possible? I would want them to all be bonded but my window guy has said it would be very hard to do as there is a fair curve on the rear and would be hard to hold it in place whilst the gunk goes off.
#19
mini-man-dan
-
- Traders
-
- 2,684 posts
Up Into Fourth
- Location: Bristol
- Local Club: J19 Mini Owners Club
Posted 31 October 2011 - 12:46 PM
Hi
They are supplied flat. We would recommend you used the stadard rubber to fit the rear window for a few reasons. Firstly they are easier to fit in with rubbers as there is no issues with holding them in place. Secondly if you ever wanted to remove the window it is much easier than if it was bonded in, and thirdly it looks a little more 'factory finish'.
Cheers
Dan
They are supplied flat. We would recommend you used the stadard rubber to fit the rear window for a few reasons. Firstly they are easier to fit in with rubbers as there is no issues with holding them in place. Secondly if you ever wanted to remove the window it is much easier than if it was bonded in, and thirdly it looks a little more 'factory finish'.
Cheers
Dan
#20
mini-man-dan
-
- Traders
-
- 2,684 posts
Up Into Fourth
- Location: Bristol
- Local Club: J19 Mini Owners Club
Posted 24 November 2011 - 05:53 PM
15% Off Xmas Special!!
Take advantage of another 5% off available until Christmas Day.
Please give Tony a call on 07977 231876 to order using a credit/debit card
#21
jonny f
-
- Members
-
- 1,485 posts
One Carb Or Two?
- Location: Surrey
- Local Club: Boxhill Mini Club
Posted 21 December 2011 - 08:47 PM
about time i gave him a call again, must have been a year.
Will call tomorrow!
Will call tomorrow!
#22
leadly
-
- Members
-
- 779 posts
One Carb Or Two?
- Location: Derby
- Local Club: [] D.C.M.O.C []
Posted 21 December 2011 - 09:07 PM
Think I may have to call tomorrow as well.
Can't miss a 15% discount!
Can't miss a 15% discount!
#23
danny1
-
- Members
-
- 1,321 posts
In the navy you can sail 7 peas
- Local Club: bumpstart
Posted 21 December 2011 - 10:04 PM
just ahd mine fitted to the mini, front and rear side ones were a doddle to fit that rears screen was a bugger.
but so happy with them
but so happy with them
#24
mini-man-dan
-
- Traders
-
- 2,684 posts
Up Into Fourth
- Location: Bristol
- Local Club: J19 Mini Owners Club
Posted 23 December 2011 - 11:10 AM
The rear screens are deliberately tight to make sure they stay where they should and not pop out. Glad you are happy with them!
Dan
Dan
Edited by mini-man-dan, 23 December 2011 - 11:10 AM.
#25
mini-man-dan
-
- Traders
-
- 2,684 posts
Up Into Fourth
- Location: Bristol
- Local Club: J19 Mini Owners Club
Posted 28 December 2011 - 11:35 AM
Hope everyone had an excellent Christmas!
Offer now back to:
10% Off for any TMF Member
Happy New Year Everyone! We will hopefully be bringing in many more products during 2012 so keep an eye out!
Offer now back to:
10% Off for any TMF Member
Happy New Year Everyone! We will hopefully be bringing in many more products during 2012 so keep an eye out!
#26
mini93
-
- Members
-
- 8,615 posts
He's just too casual!
- Location: Warwick
- Local Club: Medievil minis of Warwickshire
Posted 28 December 2011 - 05:04 PM
10% Off for any TMF Member
i choose my gut
#27
jonny f
-
- Members
-
- 1,485 posts
One Carb Or Two?
- Location: Surrey
- Local Club: Boxhill Mini Club
Posted 28 December 2011 - 06:04 PM
Whoops i forgot to call haha.
Must do it this week.
Must do it this week.
#28
mini-man-dan
-
- Traders
-
- 2,684 posts
Up Into Fourth
- Location: Bristol
- Local Club: J19 Mini Owners Club
Posted 17 January 2012 - 01:03 AM
Bumpety bump :)
#29
TheOriginalMiniator
-
- Noobies
-
- 137 posts
Mini Mad
Posted 14 February 2012 - 07:22 AM
10% offer is still on for the forseeable future!?
#30
mini-man-dan
-
- Traders
-
- 2,684 posts
Up Into Fourth
- Location: Bristol
- Local Club: J19 Mini Owners Club
Posted 18 February 2012 - 10:37 AM
Yep still on!
Edited by mini-man-dan, 18 February 2012 - 10:37 AM.
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users
