Jump to content


Photo

Podifold, The First One


  • Please log in to reply
95 replies to this topic

#61 coopdog

coopdog

    Up Into Fourth

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPip
  • 4,506 posts
  • Location: South Wales

Posted 31 December 2015 - 10:52 AM

Just leave the carb, it will clear soon enough,

I got a bit scared then thought you'd blown a ring or something haha


Can't wait for the vid!

#62 HUBBA.HUBBA

HUBBA.HUBBA

    Up Into Fourth

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPip
  • 2,823 posts
  • Location: Sutton Coldfield
  • Local Club: Loan wolf

Posted 31 December 2015 - 03:30 PM

Aready had lookstill covered in oil all round the jet. Nice and clean now

#63 Spaceibiza

Spaceibiza

    Mini Mad

  • Members
  • PipPipPipPip
  • 232 posts
  • Location: Nottingham

Posted 31 December 2015 - 09:48 PM

One thing I have noticed is because of the way I have my inlet for the charger, the induction noise is loud.
I'll get a gopro soon and film it on the go, from inside


My blow through supercharger used to be really loud!

#64 HUBBA.HUBBA

HUBBA.HUBBA

    Up Into Fourth

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPip
  • 2,823 posts
  • Location: Sutton Coldfield
  • Local Club: Loan wolf

Posted 31 December 2015 - 10:58 PM

Im currently making a cold air induction duct. Well kind of, not fully enclosed. May be quieter if I enclose it.

#65 HUBBA.HUBBA

HUBBA.HUBBA

    Up Into Fourth

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPip
  • 2,823 posts
  • Location: Sutton Coldfield
  • Local Club: Loan wolf

Posted 01 January 2016 - 03:08 PM

Here's a couple pics of my new induction duct to get as much cold air in as possible. Bonus as it also works a shield for dizzy.






#66 HUBBA.HUBBA

HUBBA.HUBBA

    Up Into Fourth

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPip
  • 2,823 posts
  • Location: Sutton Coldfield
  • Local Club: Loan wolf

Posted 14 January 2016 - 08:19 AM

IT WORKS! On the rolling road at Aldon yesterday. Now runs really well. This wasn't a power run, as I'm running things in, but for anyone had doubts about Podifold and where throttles should be( blah, blah, blah )....don't. I works! My advance is set low at the moment whilst things are running in. As soon as things are bedded in I will crank things up, have a power up and post up the figures.
I do not, repeat do not have the lag and bogging down anymore which I had on my suck through set up. Not saying a suck through set up doesn't work, its just not for me with my hif44. As soon as I buy a gopro I'll get some footage up.
Attached File  20160113_105328.jpg   101.83K   107 downloads

#67 podifold

podifold

    Suck through sucks

  • Traders
  • PipPipPipPipPip
  • 376 posts
  • Location: Manchester

Posted 14 January 2016 - 04:25 PM

Nice work HUBBA.HUBBA

 

I'm really happy about this. My main goal from day one has always been to try and overcome the drivability issues associated with suck through set-ups. If there's an increase in power as a by-product that would be fantastic, but that's not what all this has been about. There's no point having all that power on tap if you can't use it reliably when you want it!

 

Looking forward to a power run now and some long term testing of issues like carb icing and M.P.G. etc.

 

It's taken a while, but again, well done mate!


Edited by podifold, 14 January 2016 - 04:26 PM.


#68 HUBBA.HUBBA

HUBBA.HUBBA

    Up Into Fourth

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPip
  • 2,823 posts
  • Location: Sutton Coldfield
  • Local Club: Loan wolf

Posted 22 February 2016 - 04:14 PM

Had some t pieces and a flange made up to put my new bypass valve in. Very pleased with the results.

Attached File  20160216_165124.jpg   120.78K   43 downloads

Attached File  20160222_161219.jpg   120.26K   85 downloads

Attached File  20160222_161231.jpg   89.3K   43 downloads

Attached File  20160222_161239.jpg   119.22K   79 downloads

#69 DannyTip

DannyTip

    One Carb Or Two?

  • TMF+ Member
  • PipPipPipPipPipPipPip
  • 1,020 posts
  • Local Club: A Series Magpies

Posted 22 February 2016 - 04:16 PM

Bypass valve and bov? Can you please explain the setup for us mere mortals.

Edited by DannyTip, 22 February 2016 - 04:20 PM.


#70 coopdog

coopdog

    Up Into Fourth

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPip
  • 4,506 posts
  • Location: South Wales

Posted 22 February 2016 - 04:24 PM

Very nice

#71 HUBBA.HUBBA

HUBBA.HUBBA

    Up Into Fourth

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPip
  • 2,823 posts
  • Location: Sutton Coldfield
  • Local Club: Loan wolf

Posted 22 February 2016 - 05:50 PM

Bypass valve and bov? Can you please explain the setup for us mere mortals.

My bov has a really strong spring in and the lower tial one was too weak, and was stsying open nearly all the time . With the stronger spring it was very slightly opening on idle (hissing) and that was getting on my nerves. Reading up on the bypass valve I just wanted to give it a try as the general driving experience was also a bit violent. Plus I was hoping recirculation would quieten the induction noise a bit.
The result is it is quieter, getting a higher boost reading, smoother delivery of boost, the throttle is even more responsive, its quicker and more refined.
The bypass is a bini one and I have plumbed it in slightly different compared to how is on a bini. The vacuum activates it when the throttle is closed and I'm still getting the bov doing its job when the pressure builds up on the other side of the throttle. They compliment each other well. I wasn't sure if the 2 would work together, but they do.

Also Roger at Aldon said he had never seen a blow through charger without a bypass even with a bov.

Edited by HUBBA.HUBBA, 22 February 2016 - 05:53 PM.


#72 podifold

podifold

    Suck through sucks

  • Traders
  • PipPipPipPipPip
  • 376 posts
  • Location: Manchester

Posted 23 February 2016 - 09:55 AM

You got the 17% reduced pulley on yet?



#73 HUBBA.HUBBA

HUBBA.HUBBA

    Up Into Fourth

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPip
  • 2,823 posts
  • Location: Sutton Coldfield
  • Local Club: Loan wolf

Posted 23 February 2016 - 12:46 PM

You got the 17% reduced pulley on yet?

yep. 5 minute job


Edited by HUBBA.HUBBA, 23 February 2016 - 12:47 PM.


#74 jamiemack

jamiemack

    Learner Driver

  • Noobies
  • PipPip
  • 12 posts

Posted 16 March 2016 - 10:21 PM

Are there any rolling road figures for this yet? You must be close.

 

Great product, loved your instagram pictures too.



#75 HUBBA.HUBBA

HUBBA.HUBBA

    Up Into Fourth

  • TMF+ Member
  • PipPipPipPipPipPipPipPipPip
  • 2,823 posts
  • Location: Sutton Coldfield
  • Local Club: Loan wolf

Posted 18 March 2016 - 04:46 PM

Just popped these forged rockers on, so need to re torque my head nuts in a couple of weeks, before any power runs. Booked in at Aldon for a rolling road session in 3 weeks (earliest I could get in).
Attached File  20160318_155639.jpg   77.16K   47 downloads




1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users