I re done my primary gear end float clearance and it is spot on now. But I have noticed the the lock 'C' clip can slide out a hell of a lot easier... Surely it can fall out while the crank is rotating?? Or is that not possible??
Iain
6 replies to this topic
#1
IainNeon91
-
- Members
-
- 1,287 posts
One Carb Or Two?
- Location: Norwich
- Local Club: Norfolk Mini Owners Club
Posted 26 March 2014 - 03:05 PM
#2
creakyjaws5533
-
- TMF+ Member
-
- 1,195 posts
My jaw needs oiling. Where's the WD40??
- Location: Bristol
Posted 26 March 2014 - 03:40 PM
Can it be tighten a little bit by squeezing the sides of the washer?
Dont take my word but just an idea might vary between engine sizes?
Dont take my word but just an idea might vary between engine sizes?
#3
Nick Warwick
-
- TMF+ Member
-
- 1,588 posts
Camshaft & Stage Two Head
- Local Club: Sheffield mini club
Posted 26 March 2014 - 03:47 PM
Mine was similar but the flywheel will hold this in place if i am correct.
#4
IainNeon91
-
- Members
-
- 1,287 posts
One Carb Or Two?
- Location: Norwich
- Local Club: Norfolk Mini Owners Club
Posted 26 March 2014 - 05:41 PM
Mine was similar but the flywheel will hold this in place if i am correct.
Yeah I suppose it must do, it came off easily in the first place.... So it must hold in place by the flywheel
#5
HARBER07
-
- Traders
-
- 4,498 posts
Up Into Fourth
- Location: Suffolk
- Local Club: Naaa......
Posted 26 March 2014 - 07:57 PM
lol, yes the flywheel holds it all together.
#6
IainNeon91
-
- Members
-
- 1,287 posts
One Carb Or Two?
- Location: Norwich
- Local Club: Norfolk Mini Owners Club
Posted 26 March 2014 - 09:03 PM
lol, yes the flywheel holds it all together.
Not all our brains have this knowledge 
hahahaha
#7
KernowCooper
-
- Mini Docs
-
- 7,847 posts
Sparkie
- Name: Dave
- Location: The South West
- Local Club: Kernow Mini Club
Posted 26 March 2014 - 09:56 PM
Make sure its position correctly when you fit the flywheel so the C clip cant drop as the flywheel goes on
Also tagged with one or more of these keywords: engine
Mini Technical Sections →
Problems, Questions and Technical →
What Size Are These Main And Big End Bearings?Started by scottyboy805 , 19 Jul 2025  engine
|
|
|
||
engine
Mini Technical Sections →
Problems, Questions and Technical →
Spi Bad Idle And 'tapping' Engine SoundStarted by Simmi Westo , 15 Jul 2025 engine
|
|
|
||
 Answered
Mini Technical Sections →
Problems, Questions and Technical →
Help! Water In Oil Question....Started by TerryLee , 06 Jul 2025 engine
|
|
|
||
Mini Technical Sections →
Problems, Questions and Technical →
Rebuilt Engine Wont Crank With CompressionStarted by Kernreuben , 04 Jul 2025 engine, electrical
|
|
|
||
Mini Technical Sections →
Problems, Questions and Technical →
1966 Mini S - Clutch IssuesStarted by MBradbury73 , 01 Jul 2025 engine
|
|
|
2 user(s) are reading this topic
0 members, 2 guests, 0 anonymous users
