9 replies to this topic

[bengreen55]

Hi all I have had a auto electrician round today and I need to clear up a fue thing before he will come and wire it up for me

* on the dta 12 way plug are 6,7,8,9,10,11,12 outputs not sure what he means but that's what he has wrote down

*where is the speed taken from for digital dash

*spare wires in zcars loom with no conectors on orange,blue,white what's it for.

*eop connector with grey rubber round it what's it for don't seem to have anything it fits my engine is 2009 if it makes a difference.

*for iva do I need dip and main and main warning light
*do I need indicator warning light
*do I need a fog warning light
*do I need reverse lights
*can I use a ign switch and start button

I know this is a lot of info but any halp would be great I an itching to drive it now it's so close to being finished

[Chris allanson]

Ben
You need indicator warning light s
Main beam light
Fog warning light
Reverse lights
They need to be clearly marked you can either fit switches with symbols on or next to each light put a dyno tape strip with what it is on it
Also you need brake fluid warning level light
They will accept ign key and a button but there's a rule about security devices for anti theft I think you need two devices ,steering lock
Counts as one and immobiliser another
I'm a bit rusty on that side of things

Somewhere here there is a DTA wiring diagram I will see if it's available still it shows which pin outs go where on the output on the ecu

Wheel speed pick up can be taken from the bolt heads on the front disc by making a small bracket to hold the sensor so it's about two mm away from the head as it passes it
In the digi dash you can then set it up with number of bolts per revolution of wheel and rolling circumference of wheel in mm or inches
If you get stuck call me

[Chris allanson]

Sorry missed the eop plug
Post a photo I might be able to I'd it

[bengreen55]

Chears Chris I am going to struggle with a stearing lock I have got the race kit with the two bearings on I have made a bracket to hold the indicator stalks but there isn't room for a stearing lock so I may have fluffed that right up and what sensor is used as the speed sensor is it an off the shelf part or a spaciffic part to go with my digital dash I can see the wiring costing me a fortune the auto electrician wants £200 a day

[Chris allanson]

I don't think you have to have a steering lock as such but need two security devices to prevent theft
You can get the Iva manual on line just have a look at the right section
Digidash has specific sensor from memory they are not too bad price wise

If I can find the wiring diagram that will help

[Chris allanson]

Ben
If you look on the DTA and see what model it is then go on google there's wiring diagrams on there identifying which pins go to what parts of the engine
Is there a loom on the motor at all like wires to the plugs temp sensor v tec etc?
I think you will have a DTA s60

[bengreen55]

Yes mate its got a zcars loom with dta s60 management system the auto electrician I am planning on using wants to know what the spare wires and stuff are he's got to make it all work with the mini loom I would normally have a go myself but when it comes to wiring I haven't got the mentality for it I am finning a demon tweeks race dash 2 so I will have to try and get a speed sensor from them

[bengreen55]

Hi all I am now thinking I have the wiring harness for an early type r motor I have another wire now that doesn't seem to go anywhere it's got act tagged on it I have worked out the eop is oil pressure sensor with different connection but the blue orange and white wire is still a misery any info great fully received

[Chris allanson]

Ben that could be air temp sensor
The Hondas ran them it should go on intake side of inlet manifolds on std car
I'm not sure if they were used on the data system
Chris

[bengreen55]

Thanks mate I will let the auto electrician know I think he's a but baffled a bit by it all do you know any lads that could wire it all up for me who has delt with the digital dash ect and the vtec side of things I have a full mini loom and the zcar vtec loom just need putting them together and them in to the car