Community Status Updates
-
Mini-Mad-Craig
<3 <3
Feb 10 2012 03:48 PM -
toyboy396
I bet he's always there ;-)
Feb 10 2012 06:17 PM -
cooperdan
you too seriously..:-)
Feb 10 2012 06:19 PM
This status update has reached the maximum number of replies allowed
RawlinsGTR
Anyone know why my fan wouldn't turn on on my MPi, causing it to overheat? Temp gauge was working fine.
Jan 30 2012 04:15 PM
-
RawlinsGTR
Have checked B9, my headlights and horn work so it's not FL1. After Craig's advice, I hope it's not the thermoswitch. Will test again tomorrow :P
Jan 30 2012 04:48 PM -
minidaves
ither temp sensor or wiring fault. fans do fail too.
dave
Jan 30 2012 05:55 PM
RawlinsGTR
Spent around 2 hours washing and drying the mini this afternoon. Only for it to start raining as I was doing the tyre pressures. I now have a wet mini sitting in the garage, and I can't be bothered to dry it :P
Jan 28 2012 06:04 PM
-
cooperdan
i get use to this
Jan 28 2012 06:46 PM
RawlinsGTR
What tyre pressures should I use for 13 x 7 tyres? Dunlop Sport on the front and Yokohoma AE37 on the rear.
Jan 28 2012 04:56 PM
-
minimarchy
yeah
Jan 22 2012 01:10 PM
RawlinsGTR
For those that haven't read the thread, the March edition of MiniWorld is out now in shops. So you can get your L2B tickets. :)
Jan 21 2012 06:48 PM
RawlinsGTR
Is there any way to remove a sheared bleed nipple from the cylinder on a rear back plate? Without just buying new cylinder?
Jan 17 2012 04:43 PM
-
ukcooper
try a small flat blade screw driver and knock into the hole and twist, worked for me in the past.
Jan 17 2012 05:25 PM -
RawlinsGTR
I know they're no expensive, but why pay more if you don't have to? Thanks.
Jan 17 2012 05:41 PM -
oliver122
stud extractor ?
Jan 17 2012 06:35 PM
-
jbs.998
Niether does mine, lol
Jan 15 2012 03:48 PM -
iDemonix
Mine is the equivalent of a big fart, no use at all, quicker to just wipe the windshield clear.
Jan 15 2012 04:39 PM -
RawlinsGTR
Ah; I'm not talking about my car. I'm talking about my home. :S
Jan 15 2012 04:51 PM
-
RawlinsGTR
I thought it might be expensive. I knew I also needed the deep socket, but I thought it may be easier for when adjusting with shims to use the spanner. But since they look so expensive, I don't think I'm gonna do that.
Jan 14 2012 11:40 AM -
A362 TTU
http://www.lawson-his.co.uk/gedore/index.php?category1=Spanners&category2=Combination&category3=Combination (1B) AF&utm_source=froogle&utm_medium=ncpc&utm_campaign=comparison#69692
£40 quid though! :o
Jan 15 2012 03:38 PM -
RawlinsGTR
Yeah. I think I'm just gonna go for the socket, thanks.
Jan 15 2012 03:53 PM
RawlinsGTR
Will I most likely snap my brake pipe union when trying to undo it from the backplate? Or does the nut rotate freely on the metal tube?
Jan 12 2012 06:52 PM
-
benjy_18
depends how corroded it is really, get some good penetritive spray and soak it for a while before you try
Jan 12 2012 07:12 PM -
Artful Dodger
the nut should turn on the piping:)
Jan 12 2012 07:38 PM -
RawlinsGTR
Thanks for the replies :)
Jan 12 2012 07:40 PM
-
miniman24
I wouldnt mind knowing either, was thinking about ordering some stickers...
Jan 09 2012 08:01 PM -
coopdog
whats the maater with him then?
Jan 09 2012 10:05 PM
