75 replies to this topic

[daveeeeee]

Mate you're getting loads done, keep it up I plan to flipfront mine as the wing is shot, you've got me tempted to go clubman

[cookie4343]

Mate you're getting loads done, keep it up I plan to flipfront mine as the wing is shot, you've got me tempted to go clubman

Thanks mate, clubman front all the way they rule.

[JordanRaisbeck]

Nice project there mate, its nice that your making a "clubfair" lol, should be interesting to say the least. Keep it up and hope to see the results in the near future *thumbs up*

Jordan.

[daveeeeee]

Or a "Mayman" lol.

[cookie4343]

Update
So today i rolled my mini over on its side and started cleaning all the underside, it did get rarther messy and lets put it this way im never gonna go rusty, as all the wax is over me.
Lots of piccys.
When i started.

In the middle of cleaning.

Nice and clean ready for some red oxide, will be stonechiped tommorow.


Red oxided.


Missis trying to look busy.

Drivers side floor half ready just need to weld some panels in.

Edited by cookie4343, 26 September 2009 - 12:52 AM.

[daveeeeee]

Lookin good mate, I got bored after cleaning half a fuel tank, never mind trying to do the whole underside Well done.

[cookie4343]

Did some more today and the mini is looking better.
Made fresh air vent blank, seal it and bolted into exsisting holes.

Then i stonechiped the half the floor and inner wing.

Edited by cookie4343, 26 September 2009 - 12:54 AM.

[mighty mini jack]

Looking good mate.

I best start doing my sills soon!

[Ro8bieg]

looking good mate, iv just done a clubfair/ mayman lol used an original clubby front i bought for £50 about a year ago. turned out good

you planning on steel of fibreglass?

[guywithvan]

i'd say your definatly not hanging around!!!,fair play to you fella most people give up by now and sell it on lol,keep soldiering on and im sure it'll be done in no time,similar to what im doing with mine give or take a few bits.

keep up the good work

[cookie4343]

Looking good mate.

I best start doing my sills soon!

Jack get better first then get gravy finished, will be nice to see it finished as you have been at it a long time with your ups and downs.

looking good mate, iv just done a clubfair/ mayman lol used an original clubby front i bought for £50 about a year ago. turned out good

you planning on steel of fibreglass?

Im planning on fiberglass mate, will be removeable as im thinking of a saxo lump only 1124cc, but to good of an engine to scrap with the car and to be honest it's pretty nippy and fast enough for me, its 60 bhp standard but it will be haveing engine mods hopeing maybe to get it upto 70-80 bhp.

i'd say your definatly not hanging around!!!,fair play to you fella most people give up by now and sell it on lol,keep soldiering on and im sure it'll be done in no time,similar to what im doing with mine give or take a few bits.

keep up the good work

Thanks for the nice comment, it does do my head in sometimes but then i just leave it for a couple of weeks then get back to it, also i want it 100% solid before i start with any body work and body mods, thanks Again

[cookie4343]

Over 2 month's, no updates im ashamed of myself.

[mighty mini jack]

Im forwarding the motivation on from my thread dude, you've been pushing me to do work so i will push you!

Hope to see some progress soon!

[Mart!]

how's this for motivation: if you dont finish your project, Nellie here will turn in her grave, and, likely as not, jump right out of it and kick your teeth in.

[oldskoolracer]

nice work