Clubman Estate Project
Started by
icedaddyuk
, May 25 2009 05:03 PM
63 replies to this topic
#1
Posted 25 May 2009 - 05:03 PM
Picked up 'General' on Saturday morning. Lots of work on the body needed and some interior work. The engine runs pretty well but the huge jap style cans will be removed as they are far too loud. Also the seats will be replaced as they aren't really my thing.
Collected it this morning :love:
Now the bad bits .......
I forgot to take a pic of the hole in the outer sill, plus there are a few more surface rust spots but the worst are above.
Work will start probably in a couple of weeks, first stripping the interior then ordering which body parts need replacing!
Adam
Collected it this morning :love:
Now the bad bits .......
I forgot to take a pic of the hole in the outer sill, plus there are a few more surface rust spots but the worst are above.
Work will start probably in a couple of weeks, first stripping the interior then ordering which body parts need replacing!
Adam
#2
Posted 25 May 2009 - 05:35 PM
ooooooo I like, this was featured a while ago wasn't it?
Those seats don't realy suit the car do they? Comfy though, Ive got them in mine.
Anyway I realy like it, good luck with whatever your going to do too it.
Those seats don't realy suit the car do they? Comfy though, Ive got them in mine.
Anyway I realy like it, good luck with whatever your going to do too it.
#4
Posted 26 May 2009 - 07:02 PM
had a good look over the car today and the to-do list is getting longer!
Driver and passenger front floor pan
Both a-pillars
Definitely a new sill on passenger side, maybe on driver side
Rub in all surface rust and hope for the best!
Replace corners of scuttle
Strip and replace brakes
Rear sub frame mountings might need work
Cosmetic stuff:
Remove stickers
Change seats
Change steering wheel
Retrim dash
Remove bull bars
Remove sun strip
Time to purchase a MIG welder I reckon!
Driver and passenger front floor pan
Both a-pillars
Definitely a new sill on passenger side, maybe on driver side
Rub in all surface rust and hope for the best!
Replace corners of scuttle
Strip and replace brakes
Rear sub frame mountings might need work
Cosmetic stuff:
Remove stickers
Change seats
Change steering wheel
Retrim dash
Remove bull bars
Remove sun strip
Time to purchase a MIG welder I reckon!
#5
Posted 29 May 2009 - 12:11 PM
Got a couple of hours on the car last night,
Removed the bull bars, roof sticker, dixie horn, arches, sunstrip, harnesses, rear seats, passenger bucket and all carpets. The whole in the floor close to the seat mounting is a little bigger than I had noticed but not too bad.
I'll get some more pics of the floor tomorrow.
Removed the bull bars, roof sticker, dixie horn, arches, sunstrip, harnesses, rear seats, passenger bucket and all carpets. The whole in the floor close to the seat mounting is a little bigger than I had noticed but not too bad.
I'll get some more pics of the floor tomorrow.
#6
Posted 29 May 2009 - 09:38 PM
Are you keeping the big 'n' little wheels or going for same size front and rear? Either way, looks cool!
#7
Posted 29 May 2009 - 10:34 PM
HAHA that looks so cool. Whats your plan for it then as your not keeping the Dukes Of Hazzard theme?
#8
Posted 30 May 2009 - 09:04 AM
The first aim is to get it through the MOT and then secondly to tidy up the bodywork, make it solid etc.
After that, it all depends on finances! I do hope to get matching alloys for the front but might try a set of 12s to see how that looks.
After that, it all depends on finances! I do hope to get matching alloys for the front but might try a set of 12s to see how that looks.
#9
Posted 30 May 2009 - 02:49 PM
Looks nice mate.
But are the exhausts still on there?? lol
But are the exhausts still on there?? lol
#10
Posted 30 May 2009 - 05:00 PM
12s!!. bah, fit 10s while you can
#11
Posted 30 May 2009 - 09:40 PM
I like the 13s
Stripped the rest of the interior out today and rubbed down so of the surface rusting. Definitely looks like I need a new driver side wing, but was thinking of going flip front if it's possible to get that for a Clubman?
I think it's had a new driver side wing in the past. Both A-pillars have come away from the sills so will need replacing, and talking of sills the passenger side will need replacing completely. Also, as usual there is a lot of rust on the inner wing where the heater mounting is.
I've got some more pics, just need to get them off the camera. Car looks sorry for itself at the moment!
Adam
Stripped the rest of the interior out today and rubbed down so of the surface rusting. Definitely looks like I need a new driver side wing, but was thinking of going flip front if it's possible to get that for a Clubman?
I think it's had a new driver side wing in the past. Both A-pillars have come away from the sills so will need replacing, and talking of sills the passenger side will need replacing completely. Also, as usual there is a lot of rust on the inner wing where the heater mounting is.
I've got some more pics, just need to get them off the camera. Car looks sorry for itself at the moment!
Adam
#12
Posted 30 May 2009 - 09:51 PM
what you doing with the cans you selling them or keeping them?
#13
Posted 30 May 2009 - 10:02 PM
I'll sell them when I've taken them off. Probably a job for next weekend, although need to order a replacement backbox first.
#14
Posted 05 June 2009 - 09:59 AM
Well my new clarke welder turned up yesterday so I'm happy
Big up to Lawson His for a great price and quick delivery! £40 cheaper than machine mart.
Will take some more pics over the weekend.
Big up to Lawson His for a great price and quick delivery! £40 cheaper than machine mart.
Will take some more pics over the weekend.
#15
Posted 05 June 2009 - 10:07 AM
Wow was this trying to be thegeneral lee muscle car? whats with the wheels and zorst lol, its a mini not a muscle car! it looks stupid, but i hope you restore it to its original glory! good luck mate,
jordan.
jordan.
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users