Couple of pics, of my little baby just before she goes for a good thrashing on the rollers.
#16
Posted 12 June 2007 - 07:04 PM
#17
Posted 12 June 2007 - 08:28 PM
what have you done to the motor and injection etc? Just the Hydra ecu? or the throttlebodies aswell?
Cheers
#18
Posted 13 June 2007 - 09:43 AM
Have you had it tuned then on the rolling road?
what have you done to the motor and injection etc? Just the Hydra ecu? or the throttlebodies aswell?
Cheers
It got 200.5bhp on a very good dyno. I am running it standard apart from the hydra ECU and the 4-2-1 exhaust. The bhp is low as i do not have a cold air feed set up for it yet, it is breathing air in that is around 80'c! This is only till i decide what im doing and get an air temp sens. then im off back to get it fully sorted.
Still goes ok with 200bhp atm!
#19
Posted 14 June 2007 - 08:11 AM
#20
Posted 15 June 2007 - 01:10 PM
Amazing car! I see that you have the ETB dashboard. Is your dash moulding from Z cars?
yes it a zcars dash and the etb digi dash, i will post some pics of it when i get chance if you would like?
#21
Posted 15 June 2007 - 02:40 PM
Cheers
#22
Posted 16 June 2007 - 06:52 PM
can i have a close up piture? they look awesome like that , i have been looking and thining about how to mount mine for ages!!! please take close up,
spoonz
(awesoem looking machine you have there )
#23
Posted 20 June 2007 - 05:14 PM
cheers
#24
Posted 01 July 2007 - 07:48 PM
how did you attach the arches like that?
can i have a close up piture? they look awesome like that , i have been looking and thining about how to mount mine for ages!!! please take close up,
spoonz
(awesoem looking machine you have there )
bump!
#25
Posted 03 July 2007 - 12:03 PM
how did you attach the arches like that?
can i have a close up piture? they look awesome like that , i have been looking and thining about how to mount mine for ages!!! please take close up,
spoonz
(awesoem looking machine you have there )
bump!
Sorry will get some more pics next time i see my mini. I havent seen her for quite a while, I took her back to zcars to fix a problem with her wires and then they flooded. They have loads of work ona and a week behind atm. so when i get it back ill let you see them. I used the mini spares arch finisher. Need to refit the rear ones again, bit of a gap at the top.
#26
Posted 16 September 2007 - 08:36 PM
how did you attach the arches like that?
can i have a close up piture? they look awesome like that , i have been looking and thining about how to mount mine for ages!!! please take close up,
spoonz
(awesoem looking machine you have there )
bump!
Sorry will get some more pics next time i see my mini. I havent seen her for quite a while, I took her back to zcars to fix a problem with her wires and then they flooded. They have loads of work ona and a week behind atm. so when i get it back ill let you see them. I used the mini spares arch finisher. Need to refit the rear ones again, bit of a gap at the top.
any luck yet ?
where did you order your arches from ? extra wide or wide?
spoonz
#27
Posted 21 September 2007 - 10:18 AM
how did you attach the arches like that?
can i have a close up piture? they look awesome like that , i have been looking and thining about how to mount mine for ages!!! please take close up,
spoonz
(awesoem looking machine you have there )
bump!
Sorry will get some more pics next time i see my mini. I havent seen her for quite a while, I took her back to zcars to fix a problem with her wires and then they flooded. They have loads of work ona and a week behind atm. so when i get it back ill let you see them. I used the mini spares arch finisher. Need to refit the rear ones again, bit of a gap at the top.
any luck yet ?
where did you order your arches from ? extra wide or wide?
spoonz
Sorry, i have been busy doing other non mini stuff. The arches are curley standard, not wides.
#28
Posted 21 September 2007 - 10:20 AM
#29
Posted 21 September 2007 - 10:23 AM
EDIT: *wonders what it would feel like travelling at 130+ in a mini*
Edited by CooperTrooper, 21 September 2007 - 10:24 AM.
#30
Posted 21 September 2007 - 10:30 AM
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users