Took it for a session on the rollers 
rolling road 3.jpg 18.2K
8 downloads
What Did You Do To Your Mini Today
Started by
Ipod
, Apr 10 2010 07:06 PM
9789 replies to this topic
#3692
Lennyliverpool
-
- Members
-
- 329 posts
Speeding Along Now
- Location: NORTHAMPTON
- Local Club: northampton
Posted 08 April 2014 - 04:45 PM
To a drive to the Mini hospital and left a list of work to be done over winter
Now just waiting for the quote!!
#3693
Mini Manannán
-
- Members
-
- 2,860 posts
Well I'll be buggered if I can find it
- Location: Middle of the Irish Sea
- Local Club: man Estate
Posted 08 April 2014 - 05:26 PM
I got my switch panel and seat brackets fitted.
Where do you get these? I need some for my buckets as they rub the doors, cheers
If they're the same ones they're in the Trader section here on TMF: http://www.theminifo...-seat-brackets/
#3694
leaky
-
- TMF+ Member
-
- 6,890 posts
Iv never hit a penguin in the face with a casserole
- Location: Costa Del Tadley
- Local Club: Basingstoke Mini Club
Posted 08 April 2014 - 06:16 PM
I got my switch panel and seat brackets fitted.
Where do you get these? I need some for my buckets as they rub the doors, cheers
JB Fabrication
https://www.facebook...ication?fref=ts
#3695
59 Speed
-
- Members
-
- 674 posts
Formally know as Smackfiend
- Location: North West
Posted 08 April 2014 - 07:24 PM
Completed bottom end and all torqued up.
Cylinder head built up, ready to go on.
Braided lines on my front calipers attached.
Attached and tried out the seat brackets that I fabricated a few weeks ago.
Continued my quest for the correct bolts that I removed ten years ago - I really should have labeled each of the dozen or so boxes I stored them in before scattering them around the garage!
Cylinder head built up, ready to go on.
Braided lines on my front calipers attached.
Attached and tried out the seat brackets that I fabricated a few weeks ago.
Continued my quest for the correct bolts that I removed ten years ago - I really should have labeled each of the dozen or so boxes I stored them in before scattering them around the garage!
#3696
RooBoonix
-
- Members
-
- 1,225 posts
One Carb Or Two?
- Location: Essex
Posted 08 April 2014 - 09:08 PM
I put the rear seats of my new (old) interior in just so it all matched until I get the whole set re-upholstered.
Gave the engine bay a little clean and re sealed the relay and positioned it better so it's not rattling about and falling apart.
Took it out for it's first decent drive since I've had it and was very pleased 
Found out that the fuel gauge read slightly low and as it was being filled took alot less than expected (about £35-£40 to fill the tank)
Cleaned the wheels a bit
All is good!
Cameron.
#3697
Moggyton
-
- Members
-
- 1,152 posts
One Carb Or Two?
- Location: Staffordshire
- Local Club: Stone mini club
Posted 08 April 2014 - 10:36 PM
Took it for a session on the rollers
How did that go mate? All run in and running nicely now? :)
#3698
leeuk
-
- Members
-
- 681 posts
Super Mini Mad
- Location: Wednesbury
Posted 08 April 2014 - 11:14 PM
Took it for a session on the rollers
How did that go mate? All run in and running nicely now? :)
Yes mate its run in now, I've done about 850mls,
It managed 80bhp + 83lbf of torque, 5890rpm - 93.5mph.
#3699
leaky
-
- TMF+ Member
-
- 6,890 posts
Iv never hit a penguin in the face with a casserole
- Location: Costa Del Tadley
- Local Club: Basingstoke Mini Club
Posted 09 April 2014 - 06:12 PM
Cleaned it for the first time this year ready for POL this weekend!
#3700
megamini_jb
-
- Members
-
- 5,491 posts
Crazy About Mini's
- Name: Jamie
- Location: -
Posted 09 April 2014 - 06:19 PM
Damn that EG is nice! Ive got a B16 waiting to go in mine from my old ek9, but will be keeping it looking 100% stock
Edited by megamini_jb, 09 April 2014 - 06:21 PM.
#3701
BronkoMini
-
- Members
-
- 1,484 posts
One Carb Or Two?
- Location: Wiltshire
- Local Club: Mini Fixers
Posted 09 April 2014 - 06:34 PM
Cleaned, polished and waxed both of them, took ages
#3702
Richie83
-
- Members
-
- 1,495 posts
One Carb Or Two?
- Location: Somerset
Posted 09 April 2014 - 07:24 PM
Fitted some legal plates on my freshly purchased mini. Not as cool as the black and silver ones, but it still looks ace.
#3703
Mini Manannán
-
- Members
-
- 2,860 posts
Well I'll be buggered if I can find it
- Location: Middle of the Irish Sea
- Local Club: man Estate
Posted 09 April 2014 - 09:49 PM
Cursed over the rod-change roll pins 
#3704
Rocket.
-
- Members
-
- 1,441 posts
One Carb Or Two?
- Location: UK
Posted 09 April 2014 - 10:00 PM
ordered some more parts 
#3705
Moggyton
-
- Members
-
- 1,152 posts
One Carb Or Two?
- Location: Staffordshire
- Local Club: Stone mini club
Posted 10 April 2014 - 08:56 AM
Was that at the wheels?Yes mate its run in now, I've done about 850mls,How did that go mate? All run in and running nicely now? :)Took it for a session on the rollers
rolling road 3.jpg
It managed 80bhp + 83lbf of torque, 5890rpm - 93.5mph.
5 user(s) are reading this topic
0 members, 4 guests, 0 anonymous users
-
Bing (1)
